Welcome, Guest |
You have to register before you can post on our site.
|
Online Users |
There are currently 49 online users. » 0 Member(s) | 48 Guest(s) Bing
|
Latest Threads |
AT&F
Forum: WiModem232 / WiModem232 Pro
Last Post: Rudi81
Yesterday, 12:22 PM
» Replies: 4
» Views: 28
|
Utilizing WiModem to run ...
Forum: WiModem
Last Post: admin
Yesterday, 01:07 AM
» Replies: 11
» Views: 151
|
Terminal software for WB ...
Forum: WiModem232 / WiModem232 Pro
Last Post: admin
03-14-2024, 01:50 PM
» Replies: 3
» Views: 60
|
bad data packet crc-32
Forum: WiModem232 / WiModem232 Pro
Last Post: admin
03-04-2024, 08:08 PM
» Replies: 2
» Views: 56
|
NULLMODEM mode
Forum: WiModem232 / WiModem232 Pro
Last Post: admin
03-02-2024, 10:16 PM
» Replies: 14
» Views: 389
|
Noise over Audio during u...
Forum: WiModem
Last Post: admin
03-02-2024, 10:14 PM
» Replies: 34
» Views: 47,810
|
Keycap Availability
Forum: KEYCAP CAMPAIGN
Last Post: solus
02-29-2024, 11:28 AM
» Replies: 2
» Views: 142
|
special cable for Apple I...
Forum: WiModem232 / WiModem232 Pro
Last Post: admin
02-23-2024, 11:08 AM
» Replies: 1
» Views: 59
|
WiModem232 Pro!
Forum: WiModem232 / WiModem232 Pro
Last Post: admin
02-19-2024, 11:11 AM
» Replies: 17
» Views: 806
|
OLED Screen Display
Forum: WiModem232 / WiModem232 Pro
Last Post: admin
02-09-2024, 10:22 AM
» Replies: 19
» Views: 2,242
|
|
|
D64 support with disk recovery! |
Posted by: admin - 07-27-2019, 12:13 PM - Forum: Latest News
- No Replies
|
|
SCP can now generate .d64 files for use with emulators. This support uses a complex algorithm designed to recover lost data. So, disks with read errors reported on a C64 can likely be dumped to an image, completely recovering the data!
|
|
|
SCP Serial port support added! |
Posted by: admin - 06-27-2014, 02:17 PM - Forum: Latest News
- No Replies
|
|
Both SCP serial ports have been activated with v1.0 of the firmware. The default baud rate of the RS232-1 port is 250Kbps, and the default baud rate of RS232-2 port is 9600 baud. You can of course change the baud rate to anything between 300 baud and 1.25 megabaud. Changes to the baud are non-volatile, so a reset of the board will restore the default baud rates. If anyone thinks that either of these should default to a lower baud rate, please let me know.
|
|
|
ADF support with disk recovery! |
Posted by: admin - 04-09-2014, 08:40 AM - Forum: Latest News
- No Replies
|
|
SCP can now generate ADF files for use with emulators. This support uses a complex algorithm designed to recover lost data. So, disks with read errors reported on an Amiga can likely be dumped to an image, completely recovering the data!
I am working on the same support for D64 image files, recovering 1541 disks as well as ST/MSA image files, recovering Atari ST disks.
|
|
|
WinUAE beta released with SCP support! |
Posted by: admin - 03-18-2014, 01:19 PM - Forum: Latest News
- No Replies
|
|
WinUAE has been updated to support Keir's work done with E-UAE and FS-UAE.
At this point, it appears that every single type of MFM based copy protection ever made is now fully compatible with WinUAE.
Since WinUAE does not support GCR at all, any disk with dual formats (or protected by GCR data) will not work.
|
|
|
E-UAE and FS-UAE support .scp images! |
Posted by: admin - 03-17-2014, 02:31 PM - Forum: Latest News
- No Replies
|
|
Thanks to the efforts by Keir Frazer, E-UAE and FS-UAE now support .scp flux images!
I asked Toni Willen (WinUAE) to look into the changes made by Keir, and Toni has added support as well! WinUAE has not been publicly released yet with .scp support but I have been beta testing it and it works almost 100% perfect - in fact, there is only one program at this point that does not work and that is being resolved.
|
|
|
|