UP9600
#18
(10-10-2016, 06:19 AM)Zeropage Wrote: Go it working at 9600 eventually ..

For some reason I was under the impression I had to AT&K1 before switching baud.. This was incorrect.

It just works.

This is probably why you were under that impression. Per the manual:

"Q: Is the WiModem capable of more than 2400 baud?
A: Yes. The well known “UP9600” hack is built into the WiModem. You will
need to enable the hardware handshaking to use this feature at 9600 baud."

Like you, though, I found that I did not need to set AT&K1 nor did I need to set hardware handshaking in my term program. 9600 seems to be fine without it. I am sure it will be needed if I ever wanted to try 38.4k, however.  Smile


I made my settings changes in this order: 1) First the WiModem (AT*B9600), then I loaded the UP9600 driver, then set the term baud rate to 9600. I also encountered freezes when I changed to the UP9600 driver. I somehow got it set without a freeze, the saved the term configuration right away. I am using Striketerm 2014 Final but had good results with Novaterm 9.6 also.

On a different subject-- I have failed to download a single file from any C64 BBS I have connected to thus far. I remember Punter being more friendly and automatic, but I am always told to go start my download and then manually name my file. Data starts to trickle in but I then get a bunch of retries. Too bad more C64 BBSes aren't capable of using ZModem. Our terminal programs are.  Smile

Hmmm....I am wondering If I can choose Multi-Punter even for a single download.
Reply


Messages In This Thread
UP9600 - by duhproject - 07-05-2016, 12:54 PM
RE: UP9600 - by admin - 07-05-2016, 03:53 PM
RE: UP9600 - by discoball78 - 10-04-2017, 09:27 PM
RE: UP9600 - by Zeropage - 12-27-2017, 01:25 PM
RE: UP9600 - by duhproject - 07-05-2016, 04:52 PM
RE: UP9600 - by XxSwitchBladexX - 07-17-2016, 09:59 PM
RE: UP9600 - by zoggins - 07-21-2016, 08:07 AM
RE: UP9600 - by admin - 07-21-2016, 07:34 PM
RE: UP9600 - by zoggins - 07-22-2016, 09:15 PM
RE: UP9600 - by admin - 07-23-2016, 12:37 PM
RE: UP9600 - by Zeropage - 09-26-2016, 05:11 AM
RE: UP9600 - by admin - 09-26-2016, 12:15 PM
RE: UP9600 - by Zeropage - 09-26-2016, 02:35 PM
RE: UP9600 - by admin - 09-26-2016, 04:51 PM
RE: UP9600 - by Zeropage - 09-27-2016, 01:56 AM
RE: UP9600 - by Zeropage - 10-10-2016, 06:19 AM
RE: UP9600 - by jdryyz - 02-24-2018, 01:06 PM
RE: UP9600 - by admin - 10-06-2017, 11:39 AM
RE: UP9600 - by admin - 02-24-2018, 01:37 PM
RE: UP9600 - by jdryyz - 02-24-2018, 04:59 PM
RE: UP9600 - by admin - 02-24-2018, 10:01 PM
RE: UP9600 - by jdryyz - 02-25-2018, 12:28 PM
RE: UP9600 - by admin - 02-25-2018, 12:30 PM
RE: UP9600 - by jdryyz - 02-25-2018, 01:09 PM
RE: UP9600 - by admin - 02-25-2018, 06:47 PM
RE: UP9600 - by jdryyz - 02-25-2018, 07:37 PM
RE: UP9600 - by admin - 02-25-2018, 07:41 PM
RE: UP9600 - by jdryyz - 02-26-2018, 03:23 PM
RE: UP9600 - by admin - 02-26-2018, 04:20 PM
RE: UP9600 - by jdryyz - 02-28-2018, 10:37 AM
RE: UP9600 - by admin - 02-28-2018, 01:18 PM



Users browsing this thread: 2 Guest(s)