CBMSTUFF FORUM
New Cases for the WiModem232 - Printable Version

+- CBMSTUFF FORUM (https://www.cbmstuff.com/forum)
+-- Forum: CBMSTUFF PRODUCTS (https://www.cbmstuff.com/forum/forumdisplay.php?fid=1)
+--- Forum: WiModem232 (https://www.cbmstuff.com/forum/forumdisplay.php?fid=79)
+--- Thread: New Cases for the WiModem232 (/showthread.php?tid=448)

Pages: 1 2 3 4


New Cases for the WiModem232 - COREi64 - 01-12-2018

I've just completed and tested my new case designs for both the OLED and non-OLED version of Jim's WiModem232.  As with all my cases, black oxide screws and brass heatsets are used to hold the case firmly together.

For those interested, they can be found at the following links:

WiModem232 OLED Version:
https://www.shapeways.com/product/HRWYAEY62/wimodem232-oled-edition-wifi-modem-case
http://corei64.com/store/products.php?122

WiModem232:
https://www.shapeways.com/product/AT3RZ6VE9/wimodem232-wifi-modem-case
http://corei64.com/store/products.php?123

I've made them available both through my shop as well as from Shapeways.

Here are some photos:

WiModem232 OLED Case:
[Image: IMG_2722.jpg]   [Image: IMG_2726.jpg]   [Image: IMG_2730.jpg]

WiModem232 Case:
[Image: IMG_2744.jpg]   [Image: IMG_2749.jpg]   [Image: IMG_2753.jpg]

Hope you like what I've come up with!

COREi64


RE: New Cases for the WiModem232 - admin - 01-12-2018

That looks great!


RE: New Cases for the WiModem232 - COREi64 - 01-12-2018

(01-12-2018, 12:37 PM)admin Wrote: That looks great!

Thank-you, and great work on the modems BTW! Always fantastic products from you. Looking forward to whatever is coming next!

Thomas
COREi64


RE: New Cases for the WiModem232 - Byte Knight - 01-13-2018

Any plans to release the .stl file so those of us with 3D printers could print this out ourselves?


RE: New Cases for the WiModem232 - COREi64 - 01-13-2018

Hi, and thanks for your inquiry.

My designs are not open source, as such, I won't be releasing the STLs for free.

Thomas

(01-13-2018, 08:44 AM)Byte Knight Wrote: Any plans to release the .stl file so those of us with 3D printers could print this out ourselves?



RE: New Cases for the WiModem232 - mojorific - 01-15-2018

No worries.  If there isn't one from the creator put up in the next week, i'll do one up and post it on Thingiverse.  It is really quite a simple model.


RE: New Cases for the WiModem232 - admin - 01-15-2018

The case I designed is a bit too complex for normal 3D printers. I had planned on making injected molded cases, but changed my mind due to cost. There are several slides required in the tooling, which a 3D printer can't generate quite right (at least not with an Ultimaker 2+). I am looking at making cases again because of the sheer number of these that have been sold.


RE: New Cases for the WiModem232 - COREi64 - 01-15-2018

So you guys don't like mine?

COREi64


RE: New Cases for the WiModem232 - COREi64 - 01-16-2018

Here are some other colors for those curious as to what variations would look like.

All printed at 100 microns.

COREi64

[Image: IMG_2813.jpg]


RE: New Cases for the WiModem232 - admin - 01-16-2018

One of the problems reported to me with your case is that there is no way to run screws through the connector to attach it permanently to a RS-232 port or cable.  This is why I used pins in my design, which makes it so you can take it apart to do an emergency reset, but that requires very tiny pins that don't 3D print so well.