The following warnings occurred: | |||||||||||||||
Warning [2] Undefined property: MyLanguage::$archive_pages - Line: 2 - File: printthread.php(287) : eval()'d code PHP 8.1.28 (Linux)
|
Installation - Read Me First! - Printable Version +- CBMSTUFF FORUM (https://www.cbmstuff.com/forum) +-- Forum: CBMSTUFF PRODUCTS (https://www.cbmstuff.com/forum/forumdisplay.php?fid=1) +--- Forum: SuperCard Pro (https://www.cbmstuff.com/forum/forumdisplay.php?fid=3) +---- Forum: Installation and setup (https://www.cbmstuff.com/forum/forumdisplay.php?fid=5) +---- Thread: Installation - Read Me First! (/showthread.php?tid=7) Pages:
1
2
|
RE: Installation - Read Me First! - admin - 08-29-2019 You MUST install the software in Administrator mode. That error is caused by the driver not being installed, or by not having the SuperCard Pro board plugged in before running the software the first time. If you don't have the hardware you can still use the software to view some of the features. However, you would need to download the FTDI driver software from the FTDI website, using the self-installer (labeled "setup executable"). https://www.ftdichip.com/Drivers/D2XX.htm RE: Installation - Read Me First! - morduk2 - 10-26-2019 (11-01-2013, 03:17 PM)admin Wrote: Before plugging in your SuperCard Pro, you must install the software for it. Download the latest full installer and run it in ADMINISTRATOR MODE. Failure to install the software in administrator mode will result in numerous errors.I purchased a new computer and immiediatly tried to install the software for the Supercard. I am the only person listed on the computer so I assumed every time I run the computer I am the adminstator. I down loaded the softare and installed the program and got the message Run-time error 713. I then followed the steps listed above ( Windows 8.1/10 Users). When I attempted to paste in step 3, I got the message that I must be an adminstator to make changes to the windows system. I followed the proceuure listed above on my old computer and did not get this message. The card was not plugged into the computer so I'm not sure what my next step is. RE: Installation - Read Me First! - admin - 10-26-2019 If you are getting the message about not being in Administrator mode then you are definitely not in Administrator mode! What you can do is right-click on the installer program and choose the RUN AS ADMINISTRATOR option. RE: Installation - Read Me First! - morduk2 - 10-28-2019 (10-26-2019, 06:11 PM)morduk2 Wrote:Jim, I did the procedure again, and still got the run-time error 713. Copied the files to the SYS folder and again got the message I needed adminstation permission to make changes in the system. I clicked continue and it copied the file to the SySWOW 64 folder. I ran the program as an adminstrator and still the problem remains. I put my old hard drive in the new computer as a "storage drive". As a precation I removed all the SCP files on that drive. Is it possible that could be causing the problem?(11-01-2013, 03:17 PM)admin Wrote: Before plugging in your SuperCard Pro, you must install the software for it. Download the latest full installer and run it in ADMINISTRATOR MODE. Failure to install the software in administrator mode will result in numerous errors.I purchased a new computer and immiediatly tried to install the software for the Supercard. I am the only person listed on the computer so I assumed every time I run the computer I am the adminstator. I down loaded the softare and installed the program and got the message Run-time error 713. I then followed the steps listed above ( Windows 8.1/10 Users). When I attempted to paste in step 3, I got the message that I must be an adminstator to make changes to the windows system. I followed the proceuure listed above on my old computer and did not get this message. The card was not plugged into the computer so I'm not sure what my next step is. RE: Installation - Read Me First! - admin - 10-28-2019 As long as you follow the instructions above then it will work. There are several thousand people using the software just fine. Make sure you run the command console (CMD) in Administrator mode. RE: Installation - Read Me First! - morduk2 - 10-28-2019 (10-28-2019, 11:45 AM)admin Wrote: As long as you follow the instructions above then it will work. There are several thousand people using the software just fine. Make sure you run the command console (CMD) in Administrator mode. I found out what I didn't do correctly. I enter the CMD as a user and not as an adminstrator. It appears to be working. Thanks for answering my questions Jim. Sometimes ittakes awhile to get through. RE: Installation - Read Me First! - admin - 10-28-2019 Ha! No problem, I am always here to help! RE: Installation - Read Me First! - Callmejack - 08-29-2020 I have several problems with windows xp (fresh new install, sp3).The last version 2.20 won’t install, it says it’s not a valid win32 application. Before plugging the board I installed version 1.95 (in admin account, running as admin). After reboot I plugged in the board and it has a problem installing drivers (error code 39). I started scp and I had an error with msstdfmt.dll being not registered. I registered it and after reboot scp loads but the board is not recognized. In device manager there is a yellow warning besides the usb serial converter and it says that windows cannot load driver because driver may be corrupted or missing (error 39). What should I do next to fix this ? |